Tel: (205) 685-9477

sales@entechproducts.com

2539 John Hawkins Pkwy

Hoover, AL 35244 US

Wearspan for Transfer Chutes

Hudco Wearline Ceramic Lined 60" Elbows for Mississippi Power Kemper County

Hudco Fabricated & Ceramic Lined Transfer Chutes for Georgia Power Plant Scherer

Hudco Designed, Fabricated, Wearspan Ceramic Lined Crusher Bypass Chute for SCE&G

HudcoAir

 

  • Transfer Chutes
    • Turnkey Design
    • Fabrication & Ceramic Installation
    • WearSpan - Ceramic 
  • HudcoAir - Air Supported Belt Conveyor
  • MistAire - Wet Dust Extractive System
  • WearLine Ceramics

Hudco 1/16" Beaded Epoxy Wear Compound for Paper Mill 

Click on link for brochure:


MistAire® Dust Extraction System


A cost effective method to increase facility safety and improve the working environment.

The MistAire® Dust Extraction System is designed to remove volatile dust emissions generated from material handling operations. Potentially explosive dust is rendered harmless as soon as it enters the MistAire® Dust Extraction System and is combined with a liquid media. The collected mixture of liquid and dust can then be discharged to waste ponds or concentrated and returned to the original material.

The Hudco MistAire® has numerous advantages over dry “bag-house” filter collection systems including:

  • Dry “bag-house” filter systems create perfect environments for explosions while the MistAire® Dust Extraction System completely eliminates such risks.
  • Changing “bag-house” filter elements is very hazardous and requires protective gear, a fresh air supply and enclosed workspaces. The MistAire® can be serviced in non-hazardous conditions and requires no special equipment.
  • Dry “bag-house” collectors are comparatively large while the MistAire® Dust Extraction System requires far less physical space for the same CFM performance.


The Hudco MistAire® design is far superior to other dynamic wet scrubbers which rely on an axial flow impeller located in the dirty air-stream:

  • Dust Extractors which rely on an axial flow fan placed in the dirty incoming air-stream are subject to excessive wear and produce high noise levels. The Hudco MistAire® Diffuser operates as a passive system responding to the airflow from a more efficient centrifugal fan operating in clean air on the downstream side of the unit.  The passive nature of the MistAire® Diffuser eliminates wear and eventual failure.
  • High speed axial flow impellers are inherently loud and cannot be located remote from the cleaning unit. The MistAire® Fan can be located to a remote site if preferred.
  • The direct drive axial flow fan scrubbers require non-standard long shaft motors with a relatively short service life caused by stressful impeller loads. The passive diffuser in the MistAire® is well supported by two heavy duty sealed bearings for long service life.
  • Collection water used by the MistAire® can be recycled and the dust slurry concentrated and returned to the conveyor system rather than discharged after a single path to the ash pond as with the other dynamic scrubbers.
  • The limited pressure differentials of the axial flow powered scrubbers limit the system capabilities while the MistAire® Fan can be sized to fit the application with pressure drops up to 30” WG if necessary.


MistAire® 6000 Specifications

  • Airflow capacity: 3,000 – 7,000 CFM
  • System Pressure Differential: 3 – 5 “ WG.
  • Water usage: Discharged to Pond @ 8.0 GPM, Recycled to bunkers @ .2 to 1.0 GPM
  • Motor: 10 to 25 HP depending on system loads.


Each MistAire® installation is carefully designed to insure consistent velocities in the incoming air-stream to insure no dangerous accumulation in the collection ducts. Air mover selections are based on actual system design requirements.

MistAire - Wet Dust Extractive Collector

Utility Power Plant in Alabama